Loading…
Advances in micro and nano manufacturing and surface engineering proceedings of AIMTDR 2021 /
This book presents select proceedings of the 8th International and 29th All India Manufacturing Technology, Design, and Research Conference (AIMTDR 2021). It discusses the latest advances in miniature manufacturing, machining of miniature components, surface engineering, nanomaterials, nanotechnolog...
Saved in:
Corporate Authors: | , , |
---|---|
Other Authors: | , , , |
Format: | Conference Proceeding eBook |
Language: | English |
Published: |
Singapore :
Springer,
2022.
Singapore : 2022. |
Series: | Lecture notes in mechanical engineering.
|
Physical Description: |
1 online resource (361 pages). |
Subjects: | |
Online Access: | SpringerLink - Click here for access |
Contents:
- Intro
- AIMTDR 2021 Conference Core Organizing Committee
- Foreword
- Contents
- About the Editors
- Prediction of Machining Quality and Tool Wear in Micro-Turning Machine Using Machine Learning Models
- 1 Introduction
- 2 Experimental Study
- 2.1 Speed Control
- 2.2 Cutting Tool
- 2.3 Vibration Measurement
- 2.4 Surface Roughness Measurement
- 2.5 Tool Flank Wear Measurement
- 3 Machine Learning Models
- 3.1 Multilayer Perceptron
- 3.2 Random Forest (RF)
- 3.3 Regression Trees
- 3.4 Radial-Based Functions (RBF)
- 4 Results and Discussion
- 5 Conclusions
- References.
- Plasma Characterization in Ultrasonic Vibration-Assisted Micro-Electrical Discharge Machining (µ-EDM)
- 1 Introduction
- 2 Ultrasonic Vibration-Assisted EDM
- 3 Experiment Performed
- 4 Plasma Temperature and Density
- 4.1 Analysis of the Spectrum
- 4.2 Calculation of Plasma Temperature
- 4.3 Electron Density Calculation
- 5 Results and Discussions
- 5.1 Plasma Temperature
- 5.2 Electron Density
- 5.3 Effect of Ultrasonic Vibration
- 6 Conclusions
- References
- Effect of Process Parameters on Accuracy of Holes Drilled on Quartz by Micro-USM
- 1 Introduction.
- 2 Experimental Setup Details and Planning
- 3 Measurement of Responses
- 3.1 Measurement of Overcut
- 3.2 Measurement of Taper Angle
- 4 Results and Discussion
- 4.1 Variation of Overcut with Process Parameters
- 4.2 Variation of Taper Angle with Process Parameters
- 5 Conclusions
- References
- Influence of Vibration in the Nozzle Frame on the Ribbon Characterization in Planar Flow Melt Spinning Process
- 1 Introduction
- 2 Experimental
- 3 Results and Discussion
- 4 Conclusion
- References.
- Experimental Investigation into Wire Electrochemical Micro-Machining for Reduction of MicroSparks and Overcut
- 1 Introduction
- 2 Experimental Setup
- 3 Experimental Planning
- 4 Results and Discussion
- 4.1 Influence of Feed Rate on MicroSpark and Overcut
- 4.2 Influence of Machining Voltage on MicroSpark and Overcut
- 4.3 Influence of Voltage Pulse Frequency on MicroSpark and Overcut
- 4.4 Influence of PZT Tool Vibration Frequency on a Micro Spark
- 4.5 Influence of PZT Vibration Amplitude on Micro-Sparks
- 5 Controlled Parametric Micro-Slit Fabrication
- 6 Conclusions
- References.
- Influence of Voltage Pulse on Machining Accuracy in Electrochemical Micromachining
- 1 Introduction
- 2 Influence of Voltage Pulse on Machining Accuracy
- 2.1 Control of Micro-Tool Feed Rate
- 3 Experimental EMM SetUp
- 4 Experimental Planning
- 5 Experimental Result Analysis
- 6 Conclusions
- References
- A Study on the Influence of Cutting Tool Geometry on the Temperature of the Workpiece in Nanometric Cutting of Silicon
- 1 Introduction
- 2 MD Simulation
- 3 Modeling
- 4 Results and Discussion
- 4.1 Analysis of Temperature During Machining.